Companionway hood issues

Welcome to PocketShip.net! This bulletin board is for builders of the Chesapeake Light Craft-John C. Harris "PocketShip" design, a 15-foot micro cruiser sailboat built from a kit or plans.

For more information on PocketShip, click here: http://www.clcboats.com/pocketship

This site gathers PocketShip builders in one place. Here you can share photos, tips, questions, and---eventually---your sailing adventures in PocketShip! CLC will also post design updates and tips here as they come up.

We'll try to knock down spam as quickly as possible.

Moderator: John C. Harris

Forum rules
Spam or commercial posts will be deleted.
This is a civil forum: no flames or drunken tirades.
Please stay on-topic.
PocketShip's Web Page: http://www.clcboats.com/pocketship
If you need CLC customer service: http://www.clcboats.com/forms/contact_us.html
We'll try to delete spam as soon as it appears.

Re: Companionway hood issues

Postby DanaDCole on Thu Jul 06, 2017 8:11 am

Hope you finish on time. My boat was also finished in early autumn--October of 2014, but, being in Oklahoma, I was able to sail into early December. It looks like you are going to have a very fine boat, and with fewer problems than early builders, in great part due to the experiences documented in this forum.

I have one more piece of advice, gleaned from recent experience. It's possible I did not put enough coats of varnish on the timber parts. Inspection of the toe rails, hatch trim rails, gallows, rub rails, and some other varnished parts showed that the varnish was gone and water had been seeping into the wood. I also noticed what appeared to be long patches of bare wood, even on places like the fronts of the hatch trim pieces, that do not get any wear (wear and tear on rub rails toe rails is to be expected).

I'm not sure why this is happening, but either the varnish is not as tough as the paint or else I did something wrong. I put on at least four coats of the recommended Interlux Scooner Varnish. Anyway, I've rubbed these areas down with Scotch-Brite "Between Coats" pads and added two more coats of varnish (will add at least two more in the near future). I haven't had any of these issues with any of the spars, but that is probably because I have a sail cover which protects them from the weather, along with the sails.*

So, please put plenty of varnish on the timber parts you decide to varnish (five or six coats perhaps), and keep a close eye on them. I'm not going to replace any of these parts (except the gallows, which was always intended to be temporary). My idea is their appearance "adds character," and I'm sticking to it. :)

*I got an excellent custom sail cover from a craftsman in Arkansas for $250. Anyone who keeps their boat outside should add this. For information, contact Charles Huie, "captain charlie," a contributor on this forum.
DanaDCole
 
Posts: 496
Joined: Wed Sep 25, 2013 2:06 pm
Location: Stillwater, Oklahoma

Re: Companionway hood issues

Postby John C. Harris on Fri Jul 21, 2017 11:30 am

>>>>The drain holes in the companionway hood sides could be sized larger than the 1/4" stated in the manual
>>>

This has been a recurring issue with PocketShip #1, which lives outdoors about half of the year. The 1/4" drain holes at the front of the companionway hood get jammed with goo. Then the water backs up in there, sits stagnantly, and inevitably penetrates the companionway track assembly. The tracks then swell and obstruct the movement of the hatch. This happened maybe five years ago and was fixed, but cropped up again right before the WoodenBoat Show. It wasn't until I had the boat moored at the show that I noticed the hatch was really sticky. The hatch is currently in the shop being resealed with epoxy and touched up.

If the boat lives outside, poke a bit of wire in the drain holes once in awhile to make sure that pollen or tree debris hasn't clogged the drains. Making the drains larger, 3/8" or even 1/2", is probably a good tweak.

PocketShip Fitting Out Details 035.jpg
PocketShip Fitting Out Details 035.jpg (3.29 MiB) Viewed 2467 times
John C. Harris
 
Posts: 182
Joined: Thu Feb 05, 2009 12:39 pm

Re: Companionway hood issues

Postby mark48 on Mon Jul 24, 2017 8:34 am

Hi all,

The photo of fiberglassing of the companionway hood (pg. 201) suggests that FG is extending over the whole forward half of the companionway hood including the "trim" piece. I expect that the slide would then be similarly treated with FG.

Is that what other builders have done, or are you all limiting the FG to simply cover the plywood decking?

Thanks for your thoughts,
Mark
mark48
 
Posts: 123
Joined: Fri Jun 28, 2013 9:55 pm

Re: Companionway hood issues

Postby mark48 on Tue Jul 25, 2017 10:42 am

...for the benefit of future Forum visitors, the answer to my question posted above about extent of FG to cover the companionway hood (and slide) is "Yes," (from CLC staff). The FG will protect the trim pieces which otherwise are prominent places for dings, and will help bind the roof of each piece to the hardwood sides.

Thank you ,CLC, and all who contribute to the PS Forum.

Mark
mark48
 
Posts: 123
Joined: Fri Jun 28, 2013 9:55 pm

Re: Companionway hood issues

Postby riverron on Tue Jul 25, 2017 7:47 pm

Mark,
Thanks for tracking that down and clarifying what gets fiberglassed!
Ron
riverron
 
Posts: 208
Joined: Fri Aug 07, 2015 10:29 am
Location: Richmond Virginia

Re: Companionway hood issues

Postby mark48 on Sun Oct 01, 2017 9:24 pm

How have PS builders sequenced finishing the top of the cabin deck and attaching the companionway hood?

My boat has been flipped twice and is now upright to finish working on the topsides. I had intended to epoxy (and fillet) my completed companionway hood onto the cabin-top deck soon, but realize that priming and painting the then-hidden cabin top surface will be very difficult. I know one builder delayed attaching the companionway hood until the topsides was completely painted, then sanding those painted surfaces to which the companionway hood was to be epoxied late in the build.

Have any builders left the (nearly hidden) cabin top unpainted? The surface has been coated with unthickened epoxy and sanded smooth, but has it been left otherwise alone? How does it look? (I.e., can anyone tell?) :-)

Thanks,
Mark
mark48
 
Posts: 123
Joined: Fri Jun 28, 2013 9:55 pm

Re: Companionway hood issues

Postby riverron on Sat Jul 06, 2019 3:28 pm

Mark,
What did you decide on the painting? I am at this stage now and have the same question.

Have any builders left the (nearly hidden) cabin top unpainted? The surface has been coated with unthickened epoxy and sanded smooth, but has it been left otherwise alone? How does it look? (I.e., can anyone tell?) :-)


At an angle, I can see some sun getting in there, I am thinking painting or varnishing the area.

Thanks
riverron
 
Posts: 208
Joined: Fri Aug 07, 2015 10:29 am
Location: Richmond Virginia

Re: Companionway hood issues

Postby mark48 on Sat Jul 06, 2019 4:29 pm

Hi Ron,

As I recall, I reached under the installed hood with a roller-on-a-handle and brush to paint the area as best I could, knowing that the surface would be largely hidden.
Thanks for your thoughts on my lazarette.
All the best,
Mark
mark48
 
Posts: 123
Joined: Fri Jun 28, 2013 9:55 pm

Previous

Return to PocketShip Forum

Who is online

Users browsing this forum: No registered users and 3 guests