Tricks for finishing spars

Welcome to PocketShip.net! This bulletin board is for builders of the Chesapeake Light Craft-John C. Harris "PocketShip" design, a 15-foot micro cruiser sailboat built from a kit or plans.

For more information on PocketShip, click here: http://www.clcboats.com/pocketship

This site gathers PocketShip builders in one place. Here you can share photos, tips, questions, and---eventually---your sailing adventures in PocketShip! CLC will also post design updates and tips here as they come up.

We'll try to knock down spam as quickly as possible.

UPDATE: An intermittent glitch is rejecting longtime users' attempts to log in, with a message saying the IP is banned. These users have NOT been banned; the solution is to try logging in again (several times if necessary). If that doesn't work, let us know and we will force a reactivation of your account. Thank you for your patience.

Moderator: John C. Harris

Forum rules
Spam or commercial posts will be deleted.
This is a civil forum: no flames or drunken tirades.
Please stay on-topic.
PocketShip's Web Page: http://www.clcboats.com/pocketship
If you need CLC customer service: http://www.clcboats.com/forms/contact_us.html
We'll try to delete spam as soon as it appears.

Tricks for finishing spars

Postby Dmksails on Mon Sep 30, 2024 4:10 pm

HI All. I've got my spars built up and sanded. Ready for epoxy and varnish. Any tips/tricks for applying epoxy and varnish to these long pieces? I would like to do all 4 sides at once.
Dmksails
 
Posts: 17
Joined: Sat May 25, 2024 2:21 pm

Re: Tricks for finishing spars

Postby Hooky on Mon Sep 30, 2024 7:53 pm

I recall reading a previous builder inserted screws in each end and made a type of rotisserie that held the spa in the air but allowed it to rotate on its axis. This provided access to all faces of the spa.
I can’t remember if I read it in a forum post or a blog
Cheers mate Terry
Hooky
 
Posts: 99
Joined: Sat Apr 30, 2016 5:49 am
Location: Australia

Re: Tricks for finishing spars

Postby [email protected] on Tue Oct 01, 2024 11:54 am

I just laid the spars over a pair of sawhorses that were topped with a strip of molding with a sharp edge facing up and covered with packing tape.
This of course left a mark on each coat of varnish, but by the time the spars were fully varnished and installed on the boat, you would have a hard time spotting any
of the marks.

Doug
[email protected]
 
Posts: 201
Joined: Fri Sep 25, 2020 2:47 pm
Location: Princeton, NJ

Re: Tricks for finishing spars

Postby dbeck on Tue Oct 01, 2024 12:17 pm

We tried and did not like the rotisserie approach. Mainly because the spar is unstable and likes to move/roll while applying epoxy or varnish. Especially when tipping with the foam brush.

Our solution was to have a screw at one end (attached with a small line to s.th. further up) and the other end on a wedge that made minimal contact with the spar (we used a wood piece covered with transparent tape). This worked very well. After each coat, the first of the four sides will rest 'wet' on the wedge. Between coats, the trace of the edge disappears when sanding. As the only downside, the final coat of varnish will have a small trace...
.., but to be honest I don't see that any more.

Dietrich

Edit: This photo shows our setup for varnishing: One end with screw in the middle (back) hanging from the ceiling, the other end (front) resting on an edge covered with transparent tape.
ps_piccolo_boom_varnish.JPG
ps_piccolo_boom_varnish.JPG (19.31 KiB) Viewed 109 times
Last edited by dbeck on Thu Oct 03, 2024 2:05 am, edited 1 time in total.
dbeck
 
Posts: 141
Joined: Fri Dec 17, 2021 2:23 pm

Re: Tricks for finishing spars

Postby Creekboater on Wed Oct 02, 2024 11:18 am

I used the rotisserie method ( https://sisterspocketship.com/2022/10/spar-rotisserie/ ) and it worked fine for me. However, if I were doing it again, I believe I would choose the much simpler method of resting both ends on sharp edges and using a screw in one end to rotate.
http://sisterspocketship.com
* Jimmy Skiff II
* amateur for sure (builder/sailor)
* impossible to insult my intelligence
Creekboater
 
Posts: 126
Joined: Sat Nov 13, 2021 6:58 pm


Return to PocketShip Forum

Who is online

Users browsing this forum: No registered users and 2 guests